MARINE ENGINE MOUNTS R & D MARINE
R & D MARINE ENGINE MOUNTS
R & D Marine was started in 1973 after several years of development work, to manufacture a flexible shaft coupling suitable for marine use, which was both easy to fit and competitively priced. The company was started in a single garage moving to two garages after one year and then to its current location in 1976. Over the years, the factory has been completely rebuilt and now has 8000 square feet of modern factory space with all manufacturing being carried out on CNC machines.
The R & D Marine Engine Mounts are designed specifically for the rigors of marine applications. The mounts are stiff enough to absorb forward and reverse propeller thrust, yet soft enough to isolate drivetrain vibrations from the hull.To help increase the longevity of the mounts, all steel parts are zinc plated and pasivated to limit corrosion. The rubber component is covered by an oil shield to protect it from petroleum based products.R & D Marine mounts are preloaded based on the combined engine and transmission weight to limit engine movement. To facilitate in the ease of installation the mounts are height adjusting and the mounting holes in the base of the mount are slotted to assist in alignment of the drivetrain.
.jpg "Marine Engine Mounts Yennora")
R & D Marine has developed a comprehensive range of fail safe competitively priced Engine Mountings to fit all major installations for boats, sailboats and various marine applications.Shear engine mounts for boats mountings are available where good isolation is required and compression boat/marine engine mounts where there is a restriction on the available space.Installation is made as quick and easy as possible with slotted holes and height adjusting studs to simplify alignment.
Flexible Engine Mounts for Yanmar, Volvo, Beta, Bukh, Cummins, Vetus engines. Mounts for Yanmar 1GM10, 3YM30, 3YM20, 3JH4E, 3JH2E, 4JH2DTE, 4JH5E, 4JH3E, 4JH4E, 2GM20, 3GM30F, ETC. Capacity 30 - 2000 lbs per mount.
- Good vibration isolation
- Fail safe design
- Will withstand roll over test
- Competitively priced
- Wide range of stock
- Available in standard sizes
- Accepts propeller thrust
- Pre-loaded
- Slotted holes to assist alignment
- Height adjusting to simplify alignment
- Fast installation time
- Worldwide availability For more information please download PDF brochure below
How To Select (details required):
Contact our engineers at info@headlandengineering.com.au for a non obligation discussion.
Front and Rear Marine engine mounts for Yanmar Inboard Engines 1GM10, 3YM30, 3YM20, 3JH4E, 3JH2E, 4JH2DTE, 4JH5E, 4JH3E, 4JH4E, 2GM20, 3GM30F, ETC.
Below Data is required to select boat / marine Engine Mount:
1. Weight of Engine including gear box2. Suitable distance between holes on mounting base of mount3. Size of the Stud on the engine mount.4. Engine model no. can help in confirming fitment of the engine mount. 5. Yanmar engine mounts are usually selected based on the engine model no.Information can be provided to us via email or phone call. 6. Yanmar Engine mounts Y 75, Y100, Y150, Y200 are available. 7. Yanmar mounts Y50 and Y70 are also available. Please download brochure for technical details.
MARINE ENGINE MOUNTS FOR YANMAR
- Define the total weight of the engine and the transmission.
- Determine 60% of the total weight and then divide by 2 to determine the capacity of each of the rear mounts (the mounts on the tranmission side of the engine).
- Determine 40% of the total weight and then divide by 2 to determine the capacity of each of the front mounts (the mounts opposite the tranmission side of the engine).
- Determine the stud necessary stud diameter and footprint of the mount.
- Choose mount most appropriately sized for the per mount weight. When possible, choose the mount nearest the middle of the weight range.
Example:
- Engine weight is 480lbs., transmission weight is 110lbs., footprint is 4", stud diameter is 5/8".
- Total weight is 590lbs.
- 590 x .6 / 2 = 177 lbs per rear mount. Mounts required are 800-010
- 590 x .4 / 2 = 118 lbs per rear mount. Mounts required are 800-037
- Why R&D Marine Engine Mounts?
- Designed for marine use, accepts propeller and engine thrust in both directions
- Offers a fail safe design
- R & D Marine Mounts are height adjustable
- Pre-loaded to reduce movement
- Slotted holes in base to assist in alignment
- Mount types to fit all applications
EXPRESS DELIVERY ALL OVER AUSTRALIA !!! EXPORT BY FEDEX TO USA AND EUROPE AND OCEANIA, PLEASE CONTACT US!!!
Contact Form
Send us information to help select the most suitable marine engine mounts
Yanmar engine mount replacement 128377-08341 (Y75) R & D MARINE 800-070 Yanmar engine mount replacement 128377-08351 (Y100) R & D MARINE 800-071 Yanmar engine mount replacement 121370-08351/129670-08340 (Y150) R & D MARINE 800-072
RECTANGULAR SHEAR MOUNTING HEAVY DUTY
800-031 engine mounts are popular with heavy engine installations with capapcity of 311kg each mount and are extensively used with engines weighing over a ton. felxible mounts can be installed with footing spacing of 5inch to 51/2 inch with elongated holes
.jpg "RECTANGULAR SHEAR MARINE ENGINE MOUNTING")
RECTANGULAR SHEAR MOUNT
800-039 engine mounts are commonly used with small engines with 12mm stud size and are extremely long lasting
COMPRESSION MOUNTINGS- MARINE ENGINE MOUNT
Rectangular Shear Mountings
The R & D Rectangular Shear Mountings offer low height with the best combination of stiffness. Soft vertically and at right angles to the crankshaft to isolate vibration, stiff fore and aft to take the propeller thrust
This mounting has a low heights giving good vibration isolation 12mm stud 5/8" Stud
.png "Rectangular Shear Mountings Diagram")
Mount Pre-loaded 1.8mm 0.07 inch | Deflection 1.8-3.4mm 0.07-0.14 inchHeight adjusting | nut thickness : 10mm 0.39 inch 14mm 0.55 inch | Maximum height: 99mm 3.9 inch 116mm 4.57 inch
Fitted with an oil shield to protect the rubber 5/8" stud 3/4" Stud
Mount Pre-loaded 2.3mm 0.09 inch | Deflection 2.3-5.4mm 0.09-0.21 inchHeight adjusting | nut thickness : 14mm 0.55 inch 11mm 0.43 inch | Maximum height: 137mm 5.38 inch 165mm 6.5 inch
Fitted with an oil shield to protect the rubber
3/4” Stud
Mount Pre-loaded 2.3mm 0.09 inch | Deflection 2.3-5.4mm 0.09-0.21 inch Height adjusting double nut and washer thickness 25mm 0.97 inch
- Fitted with an oil shield to protect the rubber
- 5/8" stud 3/4" Stud
Mount Pre-loaded 2.3mm 0.09 inch | Deflection 2.3-5.4mm 0.09-0.21 inch Height adjusting | nut thickness: 14mm 0.55 inch 11mm 0.43 inch | Maximum height: 137mm 5.38 inch 165mm 6.5 inch
5/8" stud 3/4" Stud
Mount Pre-loaded 2.3mm 0.09 inch | Deflection 2.3-4.8mm 0.09-0.19 inch | Height adjusting | Nut thickness: 14mm 0.55 inch 11mm 0.43 inch | Maximum height: 137mm 5.38 inch 152mm 6.0 inch
Fitted with an oil shield to protect the rubber 3/4” Stud 1” Stud
Mount Pre-loaded 3mm 0.12 inch | Deflection 3-6.4mm 0.12-0.25 inch | Height adjusting double nut & washer thickness (1” UNF Stud): 31.75mm 1.25” | Height adjusting nut thickness (3/4) Stud): 16mm 0.63”
Circular Shear Mountings
This mounting is designed to give excellent vibration isolation and is fitted with an oil shield to protect the rubber 3/4" Stud
Mount Pre-loaded 3mm 0.12 inch | Deflection 3-6.4mm 0.012-0.25 inchHeight adjusting | nut thickness : 16mm 0.63 inch
.png)
This mounting is designed to give excellent vibration isolation and is fitted with an oil shield to protect the rubber 1" Stud
Mount Pre-loaded 3mm 0.12 inch | Deflection 3-6.4mm 0.012-0.25 inch Height adjusting double nut and washer thickness 31.75mm 1.25 inch
Compression Mountings
This is a low height mounting with minimum deflection
5/8” Stud
Mount Pre-loaded 1.5mm 0.06 inch | Deflection 2.3mm 0.09 inchHeight adjusting nut thickness 14mm 0.55 inch
- This mounting is a competitive, low height
- medium capacity mount giving good engine control
- 5/8" Stud
Deflection 1.65mm 0.065 inch Height adjusting nut thickness 14mm 0.55 inch
Double Acting Mountings
The Double Acting Shear Mount is a unique mounting incorporating 2 rubber elements which are pre-loaded against each other, giving excellent isolation together with good control on problem installations
5/8" stud 3/4" Stud
Mount Pre-loaded 4.8mm 0.19 inch Deflection 4.8-7.6mm 0.19-0.30 inch Height adjusting Nut thickness: 14mm 0.55 inch | 11mm 0.43 inch Maximum height 153mm 6.0 inc | 153mm 6.0 inch
Engine Mounts for Small & Medium Sized Yanmar Engines
R & D Marine introduces new Engine Mounts to their comprehensive range. The mounting is designed to be a direct replacement for the Yanmar engine mounts: Y50, Y70,Y75, Y100, Y150 and Y200, with added features of being fail safe, working within controlled limits and able to withstand a roll-over test.
Mount Pre-loaded 2.3mm 0.09inch Deflection 2.3 - 8.5mm 0.09-0.335 inch Height adjusting nut thickness 12.7mm 0.50 inch
Mount Pre-loaded 2.3mm 0.09inch Deflection 2.3 - 8.5mm 0.009-0.335 inch Height adjusting nut thickness 12.7mm 0.50 inch
R & D Marine Engine Mountings
How to select (details required)
1. Engine type, number of cylinders2. Type of gearbox and reduction ratio3. Weight of engine and gearbox combined by weighing or manufacturers literature
Weight on each front mount = W x b / 2 x (a + b)
4. Is flywheel in conventional place between the engine and gearbox5. Position of engine mounting points6. Find centre of gravity by balancing on a roller (if possible)
7. If Centre of Gravity cannot be found, assume weight distribution of 60% on rear mounts, with 40% on front mounts. (if rear mount is in line with flywheel).
.png)
ExampleTotal weight of engine and gearbox = 1200lbsDistance a (balace point to front mount) = 17 inches
Distance b (balance point to rear mount) = 14 inches
Installation Details
Maximum clearance between the underside of the height adjusting nut and top washer must not be more than 10mm. If more height is required use a spacer under the mounting casting. This applies to all mountings in the R & D Marine Range.
Units of measurement: Black Millimetres Red Inches
It all starts with one quick, no-obligation conversation!